MRK403-A【PDF 1/6 页】SW ROTARY 4P 2-3POS BLK KNOB PC

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录695

[1页]2页 3页 4页 5页

Series MR

Half-Inch Diameter Process Sealed Rotaries

General Specifications

Electrical Capacity (Resistive Load)

For MRA: 250mA @ 125V AC

For MRF or MRK:

Other Ratings

Contact Resistance:

Insulation Resistance:

Dielectric Strength:

Mechanical Life:

Electrical Life:

Range of Operating Torque:

Contact Timing:

Indexing:

0.4VA maximum @ 28V AC/DC maximum

(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)

Note: Find additional explanation of operating range in Supplement section.

10 milliohms maximum for MRA; 50 milliohms maximum for MRF & MRK

100 megohms minimum @ 500V DC

1,000V AC minimum for 1 minute minimum for MRA

500V AC minimum for 1 minute minimum for MRF & MRK

30,000 operations minimum

10,000 operations minimum

0.02 ~ 0.07Nm for MRA; 0.005 ~ 0.02Nm for MRF & MRK

Nonshorting (break-before-make)

MRA – self-cleaning, sliding contact; MRF & MRK – self-cleaning, rotary contactor disk

30°

Materials & Finishes

Shaft:

Brass with nickel plating

Stopper Plate:

Bushing/Housing:

Movable Contacts:

End Contacts & Terminals:

Common Contacts & Terminals:

Base:

Environmental Data

Operating Temperature Range:

Humidity:

Vibration:

Shock:

Sealing:

Steel with zinc plating for MRA & MRK; polyamide cover with stopper for MRF

Zinc alloy with zinc plating

Copper with silver plating for MRA; phosphor bronze with gold plating for MRF & MRK

Brass with silver plating for MRA; phosphor bronze with gold plating for MRF & MRK

Diallyl phthalate for MRA; fiberglass reinforced polyamide for MRF & MRK

–10°C through +70°C (+14°F through +158°F)

90 ~ 95% humidity for 96 hours @ 40°C (104°F)

10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning

in 1 minute; 3 right angled directions for 2 hours

50G (490m/s 2 ) acceleration (tested in 3 right angled directions, with 3 shocks in each direction)

MRK model meets IP67 of IEC60529 standards

Installation

Mounting Torque:

.686Nm (6.08 l b ? in)

Cap Installation Force:

Processing

Soldering Time & Temperature:

Cleaning:

Standards & Certifications

G16

19.6 ~ 29.4N (4.41 ~ 6.61 lbf) for MRA & MRK

Wave Soldering for MRA: See Profile A in Supplement section.

Wave Soldering for MRF & MRK: See Profile B in Supplement section.

Manual Soldering for MRA: See Profile A in Supplement section.

Manual Soldering for MRF & MRK: See Profile B in Supplement section.

Automated cleaning recommended. Stopper plate, as well as washers for MRA & MRK, must be in

place to maintain automated cleaning. See Cleaning specifications in Supplement section.

MRA, MRF, & MRK models have not been tested for UL recognition or CSA certification.

These switches are designed for use in a low-voltage, low-current, logic-level circuit.

When used as intended in a logic-level circuit, the results do not produce hazardous energy.

www.nkk.com

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式